Archive for January, 2012

Champaign County HVAC Q/A: Will Switching to Geothermal Save Me Money?

Monday, January 30th, 2012

There are simply a ton of different types of heating systems for homes in Champaign, and they are each more appropriate in different situations. However, some are certainly always going to be cheaper to operate than others, although that alone may not make one or the other right for you.

In the case of geothermal heating systems, the operating costs are definitely quite low. But those are not the only costs you will have to think about when you are considering what type of heating system to put in your home to keep your heating bills down.

Geothermal heating systems do not actually generate heat – they absorb it from the ground. Because of this, they actually use very little energy when they are running. All you are really paying to power is the fan that blows the heated air around your house. Also, because geothermal heating systems are more efficient at extracting heat in below freezing conditions than traditional heat pumps, they can continue to keep you warm on their own in more extreme conditions.

Traditional heat pumps, while they also cost very little to operate, do sometimes need to be supplemented by more conventional forms of indoor heating like a furnace when temperatures outdoors get too low. This is not the case with geothermal heat pumps, so if you live somewhere that has colder winters, a geothermal heat pump may be just what you are looking for. Of course, you can always opt for a furnace instead, but these will definitely cost more to run than either type of heat pump.

When you are trying to assess whether or not switching to a geothermal heating system will save you money, you first have to start with the heating bills you currently have. Then, factor in the cost of the geothermal heat pump installation as opposed to the installation of a more conventional system.

You are then in a position to see whether or not the amount the geothermal system will save you each month is enough to offset the higher cost of installation within a reasonable amount of time. Of course, the savings will always eventually add up over time, but if the length of time it will take you to break even is the same or longer than the expected life of the system, it is probably not worth it to invest in this type of heating.

Ivesdale Plumbing Re-Piping Tips: Warning Signs of Leaking or Broken Pipes

Friday, January 27th, 2012

The plumbing system in your Ivesdale home consists of an extensive network of pipes and fixtures that can wear down over time, even if they are well-maintained. Your pipes should be inspected at least once a year, particularly in older homes.

Some broken or leaky pipes can be repaired easily, but you may need to replace your pipes. If you have any questions or concerns about your plumbing system, call Lanz Heating & Cooling to speak with one of our certified plumbers.

Here are some warning signs of hidden leaks and broken pipes:

Abnormally High Water Bills

Unusual hikes in your water bill could indicate a leak, from broken or corroded pipes.  You should monitor your water bills to help you keep track of abnormal price increases.

Water Pressure

If you notice any sudden drops in water pressure, or if your washing machine or dishwasher takes longer to run through cycles, you could have a large leak in your pipe system. Call a plumber if it continues to be a problem.

Water Discoloration

While it could be sediment or mineral buildup getting through the municipal filtration system, water that contains red flakes or has a bitter taste could potentially indicate corrosion. You should call a professional plumber if this happens. Not only is it a health hazard, but you may need a pipe replacement.

Cast Iron Pipes in Older Homes

If you buy an older home with iron pipes, you should have them inspected by a certified plumber. Home inspectors can give a preliminary inspection, but they are not equipped or trained to provide a comprehensive inspection. Because cast iron pipes are made of rougher material than PVC piping, cast iron pipes tend to get clogged more easily, so you could have a potential disaster on your hands.

A professional plumber can provide a video camera inspection of your pipes to make sure there are no major clogs, root penetration, or corrosion on the inside of the pipe. This is why a professional plumber should handle any of the plumbing repairs in your Ivesdale home.

Call Lanz Heating & Cooling to handle all of your plumbing installation, repair, or maintenance needs.

Champaign Heating Maintenance – Another Happy Customer!

Wednesday, January 25th, 2012

Our mission statement is to operate with honesty and integrity to provide our customers with the highest quality service in the industry. That is why you know that if you get a Lanz technician to come to your house, you are getting someone who will not only do the job right, but also walk you through the process and answer all your questions. While HVAC equipment can be complicated, you should never be confused about the maintenance or repairs that are being performed on your system.

Superior customer service is one of the things that makes us standout over other plumbing and HVAC companies. Here is what Allen E. in Champaign wrote to us about his experience with one of our techinicans:

I would like to say that I was very impressed with Michael when he came to our facility to check the heat exchangers in all of our units. Michael was very professional, courteous and answered all of my questions as I looked over his shoulder. You are very lucky to have an employee like Michael, I could tell that he enjoyed his job and appreciates the company he works for! Dedicated employees like Michael are hard to find these days hold on to him! Keep up the good work Michael!

- Allen E. in Champaign

Thanks Allen! Please call us again if you need any heating repairs or maintenance during these cold winter months!

Broadlands Heating Installation Question: What Makes a Furnace High Efficiency?

Monday, January 23rd, 2012

You’ve probably heard about the new lines of high efficiency furnaces being released by popular home heating companies in Broadlands, but what exactly is different about these high efficiency devices from your current furnace? Let’s take a closer look at what a high efficiency furnace offers and why it can save you money.

Added Features

A high efficiency furnace uses familiar technology in a new way to reduce the amount of energy lost when combustion takes place. This means:

  • Sealed Combustion – Instead of open combustion which allows heat to escape during and after the combustion process, a high efficiency furnace uses a sealed chamber with carefully measured and fed airflow to burn fuel and produce heat. Exhaust heat can then be recaptured and used to heat air transferred to your air vents.
  • Two Stage Gas Valves – With a two stage gas valve, your furnace can respond to the temperature outside. There isn’t just one “on” switch. The furnace will regulate gas flow based on how much energy is needed to produce heat for your home. So, if there is a sudden burst of cold outside, the furnace will respond accordingly, but for most days when heating needs are low, it will use only the minimum amount of needed gas.
  • Programmable – High efficiency furnaces are now programmable, meaning you can set specific time limits for operation, change thermostat settings digitally and inspect the device through an electronic read out. The level of control given to you by a programmable high efficiency furnace can greatly reduce gas or electricity consumption.

Cost Benefit

The real reason many people are interested in high efficiency furnaces is that they are so much less expensive to operate. Instead of costing hundreds of dollars to run through the winter, they operate the bare minimum needed to heat your home. Using up to 95% of the fuel they consume to produce heat and regulating gas to cut how much is consumed during milder days, these furnaces are built to save you money.

If you have an old furnace in your Broadlands home that chews through energy like nobody’s business, now might be the time to consider the benefits of a brand new, high efficiency model.

Gibson City Plumbing Question: What Causes Low Water Pressure?

Friday, January 20th, 2012

Low water pressure in your Gibson City home can make just about everything from showering to cleaning more difficult. It is frustrating, but it often seems like there is very little you can do about it. In fact, you may be able to improve your water pressure in a variety of ways, but the appropriate technique will depend on the root cause of your problem.

There are several different possible causes for low water pressure. If the problem is limited to certain areas or fixtures in the house, it may very well be because the pipes feeding that area or fixture are too small. Smaller pipes will only allow a smaller amount of water to pass through at once, making it impossible for you to get the force you are after.

Fixing this, of course, means putting in larger pipes, and that may be easier said than done. However, if the problem is on a small scale, you should not have too much trouble or need to pay too much to have a professional complete the job. A problem in a particular fixture can also result from small clogs or backups in the fixture itself, and this is a relatively easy situation to remedy as well.

A low water pressure problem that affects your whole house can result if the main pipes feeding into your house are too small. This could be the case if your house has been added onto since it was built or if you have more people living there now and using more water.

Replacing those incoming pipes is a big job, but it is often the only way to increase your water pressure and make it possible for the system to satisfy the water needs of the house. This is definitely something you will want to have a Gibson City professional work on, and while it can be costly, it will be well worth it in the end.

Another possible reason that you might have low house-wide water pressure is that you live at the end of the area water system or that you use an improperly located well. If your well is downhill from your home, for instance, you should consider installing a booster pump that can help move the water into your house more efficiently. The same remedy can work if you live on the outskirts of town and at the limit of your town’s water system.

Bondville Heating Replacement Checklist: 5 Reasons to Replace the Furnace

Wednesday, January 18th, 2012

Many Bondville homes are heated with furnaces, since they generally provide safe and efficient heat.  Furnaces have also improved dramatically over the years as manufacturers find ways to make them more efficient. Even if your furnace has been reliable for many years, it may be worth the money to replace your old furnace with a newer, more efficient model.

Here are five major benefits to upgrading your furnace.

1. Lowering Your Utility Bills

Whether you realize it or not, your current furnace could be costing you more than it should in heating bills. If your furnace is 15-20 years old, it’s probably not heating your home as efficiently as the newer models with higher AFUE ratings. Even if your heating system has been replaced within the last ten years, the technology has advanced enough to consider an upgrade.

2. Fewer Repairs

Repair costs can add up if you are constantly repairing your furnace. Routine maintenance for your furnace can help reduce the need for repairs, but as furnaces age, they tend to need more repairs and replacement parts. If you need frequent repairs for your furnace, it may be time to replace it with a newer one.

3. More Consistent Heat

While maintaining consistent temperatures throughout your home involves several factors, such as insulation and thermostat control, your furnace could also be the reason you aren’t getting enough heat to all parts of the house. If some rooms are colder than others, or if your heating bills have recently gone up, it may be time for a furnace replacement.

4. Reduce the Chances of a Breakdown

When a furnace breaks down, it not only leaves you without heat, but it is also a major expense. Budgeting for a new furnace before it breaks down will put less financial burden on you than needing an emergency furnace replacement. Newer model furnaces are also more reliable and less likely to give you problems if maintained properly.

5. Safety

There’s higher potential for safety concerns with older or poorly maintained furnaces. In addition to fire hazards, carbon monoxide poisoning is another serious threat. When the heat exchanger stops working because it’s corroded or faulty, carbon monoxide can leak into the home. If you’ve had your furnace for more than 20 years, it could create safety hazards that you may be unaware of.

No matter how long you’ve had the furnace in your Bondville home, it’s always wise to speak with a qualified HVAC technician about furnace upgrades, particularly if you have expensive heating costs. Call Lanz Inc. today to talk with one of our heating experts about furnace upgrades.

Happy Martin Luther King Day from Your Champaign-Urbana Plumbing and HVAC Contractor!

Monday, January 16th, 2012

Happy Martin Luther King Day! Take some time today to think about how you, like Dr. Martin Luther King Jr., can serve your community. There are hundreds of things you can do to make this world a better place, from helping a neighbor to volunteering for your local homeless shelter. Everyone doing a little bit of extra service can make a big difference!

Buckley Plumber’s Guide: History of Plumbing

Friday, January 13th, 2012

Everyone in Buckley knows that water runs downhill, right? That’s because of gravity. And that simple theory was the key milestone in the history of plumbing. As far back as the days of the Roman Empire, people were using gravity to move water from its source to where it was used. There were no systems of piping back then and no way to pressurize a means of transporting water from one location to another.

The beauty of the gravity movement was how the Roman engineers achieved it – through the use of aqueducts. These aqueducts carried water from higher elevations in mountains to the cities below. Some of them were outdoor architectural marvels but most of the water was carried through underground tunnels. The gravity that carried the water was achieved by a slight pitch in the tunnel or aqueduct. It is estimated that as much as 300 million gallons of water found its way into Rome every day.

The fall of the Roman Empire brought the demise of this elaborate system but other plumbing marvels followed in the decades and centuries to come.

The means of transporting water changed from aqueducts and tunnels to something that was very abundant in the early stages of developing countries like the United States – namely wood. Hollowed out logs were the forefathers of modern iron pipes. These wooden pipe systems were found in the northeastern U.S. in the 1800s. Unfortunately, wood exposed to water soon deteriorated and rotted – and also left a bad taste to the water.

Iron and steel water pipes began to show up in the late 1800s in the U.S. These pipes were characterized by their heavy weight. The next generation of piping was made from copper. This material was introduced in the early 1900s and became commonly used by the middle of the century. Eventually, plastic was used to replace copper and steel. It is less expensive and just as durable.

Of course, any type of indoor plumbing was deemed a luxury for the “common” homeowner in the 1800’s and 1900’s. Indoor plumbing was not a standard and as late as the 1940s and 50s, many homes still utilized the good old fashioned outhouses as toilet facilities. That happened, in part, because towns did not have central water pumping and treatment facilities – and there were no city sewer lines to tap into. And the cost of indoor plumbing was out of some household budgets.

Today, what we take for granted in our array of indoor fixtures and appliances would have been deemed a luxury fitting to kings and queens by our ancestors. It’s no wonder we coined the phrase, “I have to go sit on the throne.”

Royal Boiler Repair Tip: Reasons for Poor Heating Performance

Wednesday, January 11th, 2012

You don’t have to be a rocket scientist or a mechanical engineer to troubleshoot – and possibly diagnose – the problems with your Royal home’s boiler when its heating performance is erratic or non-existent.

The good thing about boilers is that they are typically reliable and long-lasting. There aren’t a lot of working parts that can break down and cause problems, compared to other home heating equipment. When problems do arise, they are usually related to the expansion tank or circulating pumps. But a problem can be much simpler – like a tripped circuit breaker.

The most common problems can be noise, no heat, or poor/erratic heating. Before calling a qualified heating and cooling professional, take a moment to see if you can figure out the what’s wrong.

If you have a noisy boiler it might be because of two things – a faulty circulating pump or water trapped in the return lines. If the pump breaks it will make a loud noise when its motor runs. Water can be trapped in the return lines, which may require “re-pitching” the lines to allow for a flow back to the boiler. You may be able to adjust the flow by positioning hangers on the piping but replacing a pump is better left to a professional.

If your boiler is producing no heat, it could be because of something as simple as a circuit breaker being tripped or a fuse being blown. Check your circuit breakers and fuse and reset or replace if necessary. Is your boiler thermostat in the heat mode? It should be but if it isn’t, make the switch. If your boiler has a standing pilot you should check to see if it is lit and if not, re-light it.

Other problems would take a professional to fix. For example, no heat can be traced to low water levels in the boiler. The boiler should always be half-full of water and if it isn’t, it is likely because of leaks or a faulty pressure reducing valve. Don’t try and fix the problem by yourself.

Low water levels may not cause the boiler to lose its heating capabilities, but may cause fluctuations in its heating capacity. Again, it is advisable to call a Royal heating contractor to diagnose and fix the problem. Poor heating can also be traced to mineral deposits in the boiler. Consult your owner’s manual on instructions how to flush out the boiler.

As always, read the owner guide or operating manual for your boiler. You should get some good tips on proper maintenance and troubleshooting. And have the phone number of a qualified professional taped to your boiler – just in case.

Ivesdale Plumbing Guide: How to Fix a Slow Drain

Monday, January 9th, 2012

Ever fill up a bathroom bowl or kitchen sink with water in your Ivesdale home and then wait forever for the water to drain? A clogged drain can take forever to free up and is often the source of frustration and a loss of precious time as you get ready for work or play.

The solutions to fixing a slow drain can be very simple or complex, requiring a little patience or expertise to a major service or repair bill. Let’s hope the solution is the former and not the latter. And here are some suggestions.

If your bathroom sink is draining slowly, remove the stopper and inspect it for any “cling-ons” – namely hair. One of the most common clogs can be hair wrapped around the shaft of the stopper. Remove the hair, replace the stopper, run some hot water and check to see how quickly the water drains down. If that simple fix doesn’t work, dig a little deeper.

Hair can be tangled in the flange or the horizontal rod and clip, further down the pipe. You may need to dig out the hair or debris with a long object like a screwdriver or wire hanger. Don’t bring out the “big guns” like a snake or auger if something simpler will do the trick.

Once the debris is cleared, you may even want to use a small hand plunger to force air down the pipe and remove any other residual debris that may be slowing down the water flow. These steps should clear up the problem. A liquid or granulated drainer cleaner may also break up the clog. Running hot water can do the trick, too.

If these solutions don’t work, a slow drain could be the result of a more serious problem. At that point you may want to use a snake on the problem or call a professional plumber to fix it.

If your kitchen sink drains slowly, the problem could be a build-up of food or grease in the pipes. Once again, using a plunger or chemical drain cleaner may solve the problem. But don’t discount the fact that something may be blocking the pipes, like a piece of bone or a child’s small toy (if you have a mischievous toddler). A visual check of the problem might be the simple solution to the slow drain “mystery.”

If you are at your wit’s end and the water drainage continues to be a problem, call an Ivesdale plumber. They may even be able to walk you through a cleaning process over the phone.