Posts Tagged ‘Mahomet’

What Pesotum Residents Should Look for When Buying a 20 Year Old Home

Thursday, March 22nd, 2012

The older the home you look for in Pesotum, the more careful you need to be in your research. Of course, if you can avoid any of the major issues that crop up in 20 year old constructions, you can come away with a fantastic home that is comfortable, easy to modify and in an established neighborhood with good schools, plenty of trees, and a solid maintenance history.

The Stuff to Watch Out For

When a home reaches 20 years old, there are quite a few problems you’re likely to run into. Consider the fact that roof, air conditioner, and furnace repair is likely because all are designed to last at least 20 years. That means that unless they were highly maintained and regularly inspected they may be ready for replacement right about now.

So, when looking at homes, have any prospective purchases fully inspected for things like dry rot, termites, old furnaces and air conditioners and so on. You are also likely to run into older bathrooms and kitchens that need to be updated. For most people this is simply an inconvenience, but for those on a tight budget it can be a deal breaker.

What You Should Want

Of course, there are a lot of benefits of an older home if you can find them. Specifically in the 20 year old timeframe, you’ll find that trees have matured, the yard is well established and if the neighborhood is good, local schools will have plenty of support in the community. These are all factors you should take into consideration when looking for an older home.

Air conditioning and furnace maintenance is something you won’t be able to avoid, especially if the home you’re looking at was not well cared for by the previous owners. However, after a couple of years, even an older home can be worked into tip top shape so that nothing will break or give out unexpectedly. Much like a used car, if you do your research well ahead of time, you can be sure you get a home that won’t have any “breakdowns” for a few years to come.

And for those out there who like to customize, keep in mind that older homes are much easier to change. Newer homes are built on prefabricated slabs that make it nearly impossible to remodel or change them, especially in highly regulated areas. Older homes are easier to remodel and often have plenty of space in which to do so.  If you have any questions about appliance maintenance call Lanz Heating & Cooling.

Tags: , ,
Posted in Furnace, Furnace Maintenance, Furnace Repair | Comments Off

Royal Boiler Repair Tip: Reasons for Poor Heating Performance

Wednesday, January 11th, 2012

You don’t have to be a rocket scientist or a mechanical engineer to troubleshoot – and possibly diagnose – the problems with your Royal home’s boiler when its heating performance is erratic or non-existent.

The good thing about boilers is that they are typically reliable and long-lasting. There aren’t a lot of working parts that can break down and cause problems, compared to other home heating equipment. When problems do arise, they are usually related to the expansion tank or circulating pumps. But a problem can be much simpler – like a tripped circuit breaker.

The most common problems can be noise, no heat, or poor/erratic heating. Before calling a qualified heating and cooling professional, take a moment to see if you can figure out the what’s wrong.

If you have a noisy boiler it might be because of two things – a faulty circulating pump or water trapped in the return lines. If the pump breaks it will make a loud noise when its motor runs. Water can be trapped in the return lines, which may require “re-pitching” the lines to allow for a flow back to the boiler. You may be able to adjust the flow by positioning hangers on the piping but replacing a pump is better left to a professional.

If your boiler is producing no heat, it could be because of something as simple as a circuit breaker being tripped or a fuse being blown. Check your circuit breakers and fuse and reset or replace if necessary. Is your boiler thermostat in the heat mode? It should be but if it isn’t, make the switch. If your boiler has a standing pilot you should check to see if it is lit and if not, re-light it.

Other problems would take a professional to fix. For example, no heat can be traced to low water levels in the boiler. The boiler should always be half-full of water and if it isn’t, it is likely because of leaks or a faulty pressure reducing valve. Don’t try and fix the problem by yourself.

Low water levels may not cause the boiler to lose its heating capabilities, but may cause fluctuations in its heating capacity. Again, it is advisable to call a Royal heating contractor to diagnose and fix the problem. Poor heating can also be traced to mineral deposits in the boiler. Consult your owner’s manual on instructions how to flush out the boiler.

As always, read the owner guide or operating manual for your boiler. You should get some good tips on proper maintenance and troubleshooting. And have the phone number of a qualified professional taped to your boiler – just in case.

Tags: , , , , ,
Posted in Heating | Comments Off

Question from Penfield: How Can I Prevent Clogged Drains?

Monday, December 12th, 2011

One of the most frustrating plumbing issues any Penfield homeowner will encounter is a clogged drain. Not only are clogged drains a nuisance, they are largely avoidable, so it becomes that much more frustrating when it happens since you know that you could have taken preventative measures long before the problem occurred. To help stop your drains from clogging in the future, here are some useful preventative tips:

  • Set Cooking Grease Aside – Cooking grease is thick, viscous and clings to the sides of almost all types of pipes. So, instead of pouring it down your sink and hoping it clears out on its own, pour it into a coffee can and set it aside. There are a number of places where you can recycle old grease.
  • Flush Garbage Disposals – When you use your garbage disposal, it is imperative that you flush cold water through the system at the same time. Without water to flush the food particles through the pipes, anything ground up in the disposal will become stuck and with the application of grease or other food particles can easily become a thick clog.
  • Pour Boiling Hot Water Down the Pipes – At least once a week it is a good idea to pour 2-3 quarts of boiling water down your sinks and bathtub to loosen any pre-clogs that have formed. Things like soap, grease, food, and hair can all be dislodged by an application of hot water on a regular basis.
  • Taking Care with Your Toilet – A toilet is not designed to flush anything that will technically fit down the hole. Even for paper products that seem to be flushable, take care in what goes into the toilet bowl. Paper towels, garbage, and wrappers should not be flushed or they are likely to cause clogs.
  • Use Strainers – Install strainers on all of your sinks, including the ones in your bathroom. A simple strainer will catch excess bits of food, hair, and other grime that has a habit of falling down the drain and getting flushed along with the dishwater or during a shower.

With care, your drains will remain clog free and never require the services of a snake or a plumber. If you do get past the point of no return, do not panic just yet – there are a number of steps you can take to remove a small clog without chemicals or professional help. However, if the clog refuses to budge or begins to backup, know when to call a plumber.

Tags: , , , , ,
Posted in Plumbing | Comments Off

Troubleshooting Thermostat Issues: Is it the Thermostat or Something Else? A Guide from Sadorus

Monday, November 7th, 2011

If your room temperature is too hot or cold in your Sadorus home, what is the first thing you check? Probably the thermostat. If you are a homeowner, you probably have played around with the setting on a thermostat, much to the chagrin of other occupants who don’t share your same comfort level. And if you try and adjust a thermostat at work – well forget about it. Most companies now have locking thermostats or “false” ones that don’t actually connect to the heating and cooling system.

So if you have a temperature problem, is it really the thermostat that causes it? Maybe yes and maybe no. One physical characteristic to check is the location of the thermostat. If it is in a drafty hallway or near a heat source, it only reads the temperature for that area and other parts of the building are neglected. You will often find more than one thermostat in a home that is tied into more than one furnace or air conditioner.

The older more popular round thermostats are manually controlled and do not adjust to any conditions in the home. They simply control the heating and cooling functions based on a human turning a dial. It’s as simple as that. So if you use this method to adjust the temperatures, blame yourself and not the thermostat. You might want to consider installing a digital, programmable thermostat.

With that in mind, let’s look at some typical ways to troubleshoot a thermostat.

  • Check the anticipator, which is a small metal tab on the front of the printed scale. Give it a light push in either direction. It may be stuck.
  • Clean the interior of the thermostat housing and clean the contacts (small metal plates)
  • Check loose wires or wires that may be corroded.
  • Read the thermostat manual (if not available, look online) for other tips such as ensuring there is voltage to the terminals.

If you have checked everything and the thermostat seems to be in working order, look for other things within the heating & cooling system. These include blocked or restricted registers and vents, leaks or cracks in ductwork, and dirty air handling filters.

Tags: , , , , , ,
Posted in Heating | Comments Off

How is Geothermal Different than Other Heating Systems? A Question from Gifford

Friday, October 21st, 2011

There are many methods to heating a building in Gifford. Early methods included burning coal and wood. Today, sophisticated building controls call for more efficient means of heat – and a method gaining in popularity is geothermal heating.

Many use air handling units to deliver heat – and that method has remained constant over the years. But air handling units are only designed to move air from one space to another. How that air is heated from the source is what differentiates geothermal from other energy sources.

To understand some of the differences, let’s look at the definition of geothermal heat. By definition, geothermal heating comes from its direct use of geothermal energy, which comes from below the Earth’s surface. And the Earth is known as the greatest conductor of heat. The constant, renewable temperature of the Earth (56-58 degrees on average below 10 feet) provides a heat source requiring no energy conversion, which adds to heating efficiency and ultimately, the cost to heat a building.

In order to heat a building, natural heat from the ground absorbs a colder refrigerant, which is circulated throughout the ground by a series of polyethelene tubing, which is generally positioned five to ten feet below the surface. This heat is transported via the refrigerant to a compressor inside a heat pump, where it is compressed and the lower temperatures are transformed from around 50 degrees to temperatures much higher, as high as 100 degrees of more. This hotter refrigerant is circulated through the tubing within an air handling unit, where colder return interior air absorbs the heat. The heated air is then carried to a building’s interior via fans. The refrigerant, with the heat removed, now becomes colder as is re-circulated into the ground to absorb the natural, renewable heat. In essence, the ground provides free heat.

Other methods of heating include forced air natural gas, oil, solar, propane, electric, radiant, and steam. Each heat source requires mechanical means to heat up the supply air. For example, natural gas – which is used to heat about half of all U.S. homes – is heated via a heat exchanger in a mechanical furnace, which runs on electricity. Radiant or steam heat is generated by mechanically raising the temperature of water or refrigerant via electricity. These methods differ from geothermal because the natural heat of the Earth provides the means for raising the temperature of the refrigerant used to transport heat to the air handling unit.

One drawback to using geothermal heat compared to other energy sources is the cost to bring this natural heating method into a building. The initial installation of a geothermal heating system is much higher than conventional natural gas heating – for example – because of the cost to install the tubing called a ground loop beneath the Earth’s surface. No other heat source, other than radiant heat, requires a series of tubing to deliver heat. But then again, radiant heat does not require a ductwork system to transport heated air or remove colder air. Geothermal requires a series of metals tubes to heat the refrigerant and the ductwork to move the heated air throughout the building.

On the flip side, its energy efficiency – using the Earth’s natural heat – is much greater than other heating sources resulting in lower utility costs, often fractions of the cost to use other heat sources. Energy savings could pay for the cost of installing the geothermal system over several years – another characteristic of geothermal heating.

Tags: , , , , , ,
Posted in Geothermal | Comments Off

Why Choose a Programmable Thermostat? A Tip From Ogden

Friday, September 23rd, 2011

There are many types of thermostats available for your Ogden home, but which is the best for your particular needs? It depends largely on how often you are home, how many rooms you have and how people in your house use each of those rooms.

A programmable thermostat in particular is a great option because it allows home owners to control when and how much heat or cooling is introduced to their indoor air. Normal thermostats lack this level of control, largely because they are built as simple switches that flip on whenever your temperature gets too low or too high.

Situations for a Programmable Thermostat

When you leave your home every day, you have two options. Either set the heat and AC so you’ll be comfortable when you return, or turn them off completely and suffer through the first half hour or so when you get home that night.

If you choose the former, you’ll pay a lot more in energy bills to heat or cool an empty house. And if your humidity levels need controlling as well, this may be your only option. Those in the second camp are forced to endure uncomfortable temperatures right when they get home and want nothing more than to relax. Not much better.

That’s why so many homeowners are opting for programmable thermostats to overcome this issue. With a programmable model, you can actually tell your home’s comfort system when to turn on and off each day, depending on when people will be there. Imagine going on vacation for three or four days and coming home to a nice and toasty living room and a smaller heating bill to go with it. That’s the kind of control a programmable model offers.

Zone Control and Beyond

Some programmable thermostats even allow you to section your home off into zones and choose specific temperatures for different areas of the house. This allows a great deal more control over when and how your system will operate each day, depending on the individual comfort needs of your family.

If you’re making dinner and don’t want the heat blasting you while you’re standing over the stove, just set the kitchen temperature lower. And with a programmable thermostat, you can tell it to come back on an hour after you leave the kitchen so that it’s comfortable later when you need a glass of water.

Tags: , , , , ,
Posted in Energy Savings | Comments Off

What Types of Air Conditioning Systems Are There? A Question From Bellflower

Monday, September 5th, 2011

Picking out the right air conditioning system for your Bellflower home can actually involve a lot of steps. There are many factors to consider and you will need to understand how each type of air conditioning system functions to know what will be best in your house. Of course, before you can compare them, you need to know what the different types of air conditioning systems actually are.

Packaged air conditioning systems are probably the type that the majority of people are most familiar with. They consist of an outdoor compressor unit that is connected to an indoor air handler or furnace through ductwork within the house. The air is cooled by the compressor and then blown into the house where it is circulated through the ductwork by the air handler.

Packaged air conditioning systems are appropriate for most residential buildings and they come in a variety of sizes so that it is easy to match one to the size and dimensions of your home. However, these types of air conditioning systems do require ductwork, so if you do not already have it installed in your house, putting it in can add considerably to the overall installation costs.

If you do not want to have ducts put in or if you are only trying to cool a small space within your home, you may want to opt for a ductless mini-split system. These types of air conditioning systems are becoming more and more popular because of their excellent energy efficiency and flexibility when it comes to installation options.

Ductless mini-splits also require an outdoor compressor unit, but this is connected to one or more indoor units through refrigerant lines rather than actual air ducts. These refrigerant lines are much easier and less costly to put in place than ducts are, so mini-split systems can be installed for much less than a packaged air conditioning system in a home that does not already have ducts.

These ductless mini-split systems can include only one or many indoor units. Each of these units is controlled independently of the others, making it possible to maintain different temperatures in different parts of your home.

For larger buildings and commercial spaces, central air conditioning systems are generally the preferred option. They are set up essentially the same way as packaged air conditioning systems but on a much larger scale. However, just like packaged air conditioning systems, central air conditioners rely on ducts to get the cooled air to the various areas of the building.

Tags: , , , ,
Posted in Air Conditioning | Comments Off

Why You Cannot Neglect AC Maintenance: A Tip From Arthur

Wednesday, August 31st, 2011

Especially if you have just purchased a new air conditioning system for your home in Arthur, maintenance is probably the last thing you are thinking about. In fact, if you are like most people, you do not think about your air conditioning system at all until it does not work when you need it. But if you simply continue to use your air conditioning system without maintaining it, you will be setting yourself up for a lot of problems later on.

Just like your car or any other machine that you run on a regular basis, your air conditioning system requires a regular tune up to keep it running like it is supposed to. The type of air conditioning system you have will dictate exactly how often this maintenance service needs to take place, but most systems benefit greatly from having a tune up once a year.

When you have just purchased an air conditioning system, the last thing you probably want to do is shell out a bunch of extra cash when the system is still running fine. But it really is much cheaper to pay now rather than waiting until you have a problem with your air conditioner to call for service.

During a regular maintenance visit, your technician will examine all of the component parts of your air conditioning system to make sure that they are working the way they should and not showing any signs of excess wear and tear. This is a great way to detect problems early, even when they have not yet begun to show in the air conditioner’s performance.

Your air conditioning technician will also thoroughly clean out your system to ensure that no excess debris is allowed to build up around the coil or other vital parts of the air conditioner. This is important because it helps the air conditioner to continue to function at peak energy efficiency levels. Without regular maintenance, your air conditioner will gradually lose efficiency over time. It will only lose a little bit every year, but if you do not do something to stop it, those little bits will quickly add up.

Regular maintenance also helps to prevent more costly and inconvenient repair visits later on. And it will certainly help to increase the lifespan of your air conditioner as well. Whether you have just purchased an air conditioning system or have had yours for several years, it is never too late to start your annual maintenance visits.

Tags: , , , ,
Posted in Air Conditioning | Comments Off

How Do I Check for a Dirty Evaporator Coil? A Question From Springfield

Wednesday, August 17th, 2011

The evaporator coil is an essential piece of your air conditioning system, in Springfield or anywhere. It absorbs heat from air that passes over it, and that air then travels into your home to cool it. So if your coil is dirty or isn’t functioning properly, the cooling power of your air conditioning system is diminished. Fortunately, this problem is fixed easily by cleaning the evaporator coil. You can do this on your own or have a professional come in to take care of it.

Signs of a Dirty Evaporator Coil

The most obvious sign of a dirty evaporator coil is an overall drop in system pressure. As long as you know what constitutes a normal pressure for your system, you should be able to tell if the current pressure is below that level. If it is, a dirty evaporator coil is probably your culprit. You can also check the static pressure in your system to see if that is low, but this requires specialized equipment.

Even if you don’t notice any particular signs that your air conditioning system isn’t working properly, it’s a good idea to clean your evaporator coils once a year or so. This can help prevent any larger problems from developing in the future.

Finding Your Coil

Probably the hardest part of cleaning an evaporator coil is reaching it. Unlike your condenser coil, which is located in your outdoor condenser unit, the evaporator coil is found inside near the air handler or furnace. If you have the owner’s manual, there should be detailed instructions telling you where the coil is and how to safely access it.

Alternately, you can have an HVAC technician show you what to do the next time they come out to work on your system. Whatever you do, though, make sure that power to your AC unit is completely shut off before you start working on it. Once you’ve gained access to the coil, use a brush or vacuum attachment to remove any debris or sediment you find there.

The Importance of Maintenance

Cleaning your evaporator coil is only one part of the regular maintenance required to keep your air conditioning system in good working order for the foreseeable future. There are plenty of things you can do on your own, but it pays to have a professional come out once a year or so to check out the entire system and make any necessary repairs.

Tags: , , , ,
Posted in Air Conditioning | Comments Off