Posts Tagged ‘Seymour’

White Heath Plumbers Guide: How to Install a Toilet

Tuesday, January 3rd, 2012

Your White Heath home’s toilet is a relatively basic piece of plumbing equipment, but that does not mean that installing it is easy. This is certainly a job that many people can do on their own, but you should be prepared to devote the majority of your day to the project. While the installation itself is not terribly complicated, it is quite important that you get it right, so make sure you have all of the necessary materials, equipment and tools before you begin.

The first thing to remember is that you need to install your toilet in an appropriate place relative to the rest of your bathroom plumbing. Especially if you are installing your toilet along a branch drain, make sure that the sink, shower and any other plumbing fixtures are upstream of the spot where you will be installing the toilet.

You will also need to make sure that you install the toilet an appropriate distance from the wall. You need to be able to get around the toilet, and you also want to leave space so that work can be performed on the unit later. Putting your toilet too close to the wall can cause all kinds of complications in the way the unit functions and there is also a possibility of condensation build-up. For all of these reasons, it is important to make sure you are allowing an adequate amount of space on all sides.

The procedure you will have to follow when installing a toilet will be slightly different depending on whether you are installing it in a new spot or simply replacing an existing unit. When replacing an old toilet, you need to remove everything involved in the previous installation. That means taking the old bolts out of the floor and scraping away any residue to ensure that you have a clean and even surface to begin your installation on.

You should also make sure that you are aware of all applicable local codes before you begin your work. Even if you technically install your toilet correctly, you could run into trouble later on if your installation is not actually up to code. It is also important to remember to level all of your fixtures before you complete the installation process and to make sure you use a dielectric or brass fitting when attaching galvanized steel and copper to each other.

Tags: , , , , , ,
Posted in Plumbing | Comments Off

Pros and Cons of Various Heating Systems in Gibson City

Friday, December 16th, 2011

When it comes time to install a new heating system in your Gibson City home, there are a lot of options to consider. Many people get overwhelmed when confronted with all of the furnaces, boilers and heat pumps on the market these days. So, to help you get a handle on what each has to offer and which will offer you the best benefits, here is an overview of the modern heating system market.

Furnaces

Furnaces are the core of a forced air heating system and use gas, oil or electricity to heat air which is then circulated through your home by a blower in your air handler. Furnaces are among the most fuel efficient heating systems on the market today with options available at up to 95% AFUE (meaning it uses up to 95% of the fuel consumed to produce heat). They are also inexpensive to install and while they don’t last quite as long as boilers, they are highly efficient when well cared for.

Boilers

Boilers use gas, oil or electricity to heat water or steam which is then circulated through your home into radiators or baseboard heaters. The heated water or steam releases heat into your home and heats it in turn. While not quite as energy efficient as a high efficiency furnace, boiler heat is perfect for homes with existing radiators and no room for vents and ductwork. It also has less of an impact on indoor air quality since there is no air movement and boilers tend to last a very long time when well maintained.

Heat Pumps

Heat pumps are becoming increasingly popular, especially in milder climates where it rarely gets below 40 degrees F. A heat pump uses the same technology as an air conditioner to extract heat from outside using a compressor, evaporator coils, and condenser coils with refrigerant.

It is most efficient in the spring and fall when temperatures are mild, but it uses much less energy than either a boiler or furnace and it can be used in the summer to cool your home. When properly maintained, a heat pump will last 10-20 years and save quite a bit of money, though it is recommended that you have an emergency heat source for days when the temperature outside gets below 40 degrees F.

Tags: , , , , , , ,
Posted in Heat Pumps | Comments Off

Five Important HVAC Maintenance Tips from a Champaign Contractor

Monday, November 28th, 2011

Do you have a “mental checklist” of chores that need to be done a regular basis around your Champaign home, such as cleaning the window treatments, washing windows, shampooing rugs, etc.? There are various areas of your home that need regular maintenance and cleaning – and that list includes your heating and cooling (HVAC) equipment. Do you know a poorly operating furnace can cost you in increased energy usage and higher utility bills? That same poorly operating furnace can be discharging harmful carbon monoxide gas into your home, creating a health risk.

So, it is important to keep your furnace in peak operating condition and the best way to do that is by making a checklist of HVAC maintenance tasks. Let’s look at five of them.

  1. Check your filters. Routine replacement of your furnace filters should be every 1-3 months, depending on the indoor air quality of your home, number of occupants, size, etc. You can purchase disposable filters online, at a local “big box’ retailer, or from your local HVAC contractor. A visual inspection of your filter is the best way to determine if it needs replacing. If you have a removable electronic filter, it should be cleaned every few months using soapy water and a hose. Any restrictions to air flow through the filters can lead to poor indoor air quality and will cause your furnace to work even harder to circulate warm air through your duct system.
  2. Clean and insect the blower assembly and motor. You can do this with a vacuum. Also check the fan belt to make sure it is not too loose or if it has any cracks or splits.
  3. Look for any obstructions in vents and returns. Believe it or not, your furnace needs “help” to operate. Any build-up of dirt or debris around the grilles of your ventilation system will just make your furnace work a lot harder. Do a visual check inside and outside and pay special attention to flues and chimneys, where indoor air is exhausted. Any blockage can result in an accumulation of poisonous carbon monoxide gas.
  4. Keep the area clean and clear around your furnace and water heater. Never store flammable liquids near your heating equipment. Your furnace room is not a storage closet.
  5. Revisit your home’s insulation. When was the last time you checked out the insulation in your attic or crawlspace? Is it securely in place or drooping down? Are there bald spots where the insulation has deteriorated? Is the insulation sufficient or should it be upgrade?

Tags: , , , , ,
Posted in Heating | Comments Off

How do I Check a Gas Furnace Draft Pressure Switch? A Question from Bondville

Wednesday, November 9th, 2011

There are many reasons why a furnace stops working and in many cases, a Bondville homeowner can perform some simple diagnostics to pinpoint the problem. Finding the problem is one thing – fixing it is another. When in doubt, don’t try it yourself. Call a qualified professional.

But let’s look at one possible problem and solution you may be able to perform yourself – testing the draft pressure switch. The draft pressure switch on a gas furnace allows an electrical current to pass through to ignite the furnace. The pressure switch monitors the draft conditions and won’t allow the furnace’s gas valve to open unless draft is correct.

If the switch is malfunctioning, so too will (or will not) the furnace.

The best way to locate the switch is by consulting with your owner’s manual or by going online and simply typing in the words “gas furnace draft switch.” It is identifiable by its round size and is bolted to the outside of the furnace. It should be nearby the draft inducer motor because the two are connected by a metal tube. The tube may sometimes be the culprit, too. A tube that is blocked with condensation may cause the switch to go bad.

To check for proper function, first turn off power to the furnace, either by shutting down the “on’ switch at the furnace or shutting off the circuit breaker.

Use a volt ohm meter to check if the switch is opening and closing properly. Start by zeroing out the meter’s probes by touching the tips together. Using the dial (could be analog or digital), set the meter to 24 volts. Ground the black probe by attaching it to any metal part of the furnace. Then place the end of the red probe on the metal tube connecting the draft pressure switch to the draft inducer motor.

If the switch is working properly the meter should read at least 24 volts, or very near that. If the reading is short of 24 volts, the switch is not working correctly. At that point you may decide to replace it or call a professional to do the task (recommended).

Always remember that there are many sources which will help you diagnose and repair a problem, especially those available through the Internet. If you search YouTube.com you will find many videos advising you on how to repair certain components. Use all of the resources available to you and keep the phone number of a qualified and professional heating and cooling contractor nearby.

Tags: , , , , ,
Posted in Heating | Comments Off

When Should You Replace Your Existing Heat Pump? A Guide from Buckley

Wednesday, October 19th, 2011

Nobody wants to think about having to replace a home heating and cooling system in Buckley. It’s a big job and a new system probably won’t come cheap – not if it’s worth buying anyway. But in the end, you’ll be better off replacing your heat pump sooner rather than later if you start noticing signs that it may be on its way out.

So what are these signs? Well, they’re actually pretty easy to recognize if you know what to look for. For instance, if your heat pump is suddenly making more noise than it used to, there’s a good chance that something’s going wrong inside. This may only require a minor repair, but if minor repairs like this become a regular occurrence, you should start seriously thinking about looking around for a new system.

The cost of even minor repairs will certainly add up quickly over time, and you’ll have to seriously think about whether it makes financial sense to continue to repair an older system rather than simply replacing it with a new one. Chances are that you’ll have to invest in a new one anyway, and the sooner you do it, the less you’ll have paid for repairs to a system you were just going to get rid of anyway.

Also, if you’re starting to notice humidity problems in your home or if some parts of your house are being kept warmer than others, it may very well be a sign that you heat pump isn’t working like it should. Again, this can sometimes be rectified with repair work, but especially if your heat pump is 10 years old or more, it probably makes more sense to replace it.

Another item to keep an eye on when you’re worried about how well your heat pump is working is your monthly energy bill. If you notice a sudden or even a gradual but steady increase over time that you know isn’t a result of an increase in energy prices in your area, you should suspect that your heat pump isn’t working like it should.

Even if it’s still keeping your home at a comfortable temperature, the fact that your heat pump is using more energy to do it is a sign that there’s something wrong with your system. Plus, newer systems are generally more energy efficient anyway, so you’ll be making up for the initial investment of purchasing a new system when you start paying even less on your monthly energy bills.

Tags: , , , , , ,
Posted in Heat Pumps | Comments Off

Furnace Fan Doesn’t Run? Why Is That? What Should You Do? Some Advice From Fisher

Wednesday, October 12th, 2011

There are several reasons that a furnace fan might stop working at one point or another. While many of these do require Fisher contractor‘s attention, there are probably some things you can check on your own before you go and call in the pros. After all, if you can address the problem on your own, it will at least save you from having to pay a technician to come out.

The first thing to check when your furnace is running but the fan isn’t turning is whether or not the fan is actually switched on. Certain models of furnaces have a separate switch to turn the fan on and off. While there is probably no reason that you would want to turn off the fan by itself, it’s worth taking a look just in case. If that really is the problem, you’ll be up and running and back to dealing with better things in no time.

If that’s not the problem, you might try looking to see if any wires leading to the fan are loose or the fuse is blown. If the fan has no power, of course, it won’t be able to work but the rest of the furnace likely would work just fine as long as it doesn’t run on electricity as well.

Of course, the problem very well may be beyond your power to solve on your own. Don’t despair though. Even though you need to call in a professional, that doesn’t mean that the problem will be expensive to fix. In fact, it may be as simple as replacing your thermostat or the motor for the fan itself.

Just because a fan isn’t working doesn’t mean that you’re going to be paying an arm and a leg to have work done on your furnace. If you can’t easily discover the problem on your own, however, or if you’re not comfortable inspecting this type of equipment at all, you’re generally better off just calling in an expert and letting them do the dirty work for you. Paying for simple furnace fan repairs is definitely preferable to having to pay someone to fix the fan and the stuff you broke yourself while trying to fix the fan on your own.

Tags: , , , , ,
Posted in Heating | Comments Off

Cooling Your House Naturally in Bondville

Monday, August 8th, 2011

In this day and age, it seems like no matter what type of problem you have, there’s a technological solution for it. But is that solution always the best? For instance, just because you can get a high-tech air conditioning system to keep your Bondville home at the same temperature regardless of the weather outside, does that mean that you should rely solely on that system?

Of course, the choice is yours, but before you decide how best to keep your house comfortable during the warm summer months, it’s a good idea to learn a little bit more about what your other options might be.

  • Cross-Ventilation – One of the easiest ways to take the edge off when the temperature starts to rise inside is to open windows on both sides of the house. This allows the breeze to come in one side and pass out the other, taking the stale, warm indoor air with it in the process and cooling off your house naturally.
  • Stack-Ventilation – If you have a two-story home, you may want to try stack-ventilation. This variation on cross-ventilation involves opening the windows on the bottom floor on one side of your home and on the top floor on the other. The differences in pressure from one area to the next cause fresh outdoor air to be sucked in on the ground floor and pushed out on the top floor, thereby creating a strong air current throughout your home.
  • Blocking Out the Sun – The number one reason that the interior of your house gets hot in the summer is exposure to direct sunlight, so anything you can do to diminish the amount of sun that actually makes it into your home, the better off you’ll be. All you really have to do is close the blinds on those windows where sun can come in to keep the majority of that heat from impacting your indoor environment.
  • Stay Away from Dark Colors – The color of the outside of your home can also have an impact on how hot it gets indoors. Dark colors absorb the heat, while light colors reflect it. So if you want to keep the temperature down inside, stick to light colors on the exterior of your home.
  • The Importance of Shade – Any type of shade will also keep the sun’s heat out of your home. Trees are a great source of natural shade. Awnings can provide great cooling power too without blocking out your view.

Tags: , , , ,
Posted in Air Conditioning | Comments Off